ปรีโฟโนพร้อมไลน์สเตจท์คุณาภพห้าดาว หนึ่งในโฟโนที่ดีที่สุดในตลาดขณะนี้ เหมาะกับออดิโอไฟล์ที่คลั่งแผ่นเสียง ยอดขายไปแล้วกว่า 20 ตัวจนถึงขณะนี้รับประกันคุณภาพ เสียงดีทาก Noise ต่ำสุด ๆ ไดนามิคสูงยิ่ง ต้องฟังดู

Manley STEELHEAD® Features And Specifications
Vacuum tube compliment: 6922 SOVTEK Russian x 2 (gain) plus JAN NOS GE 7044 x 4 (output buffers)
Fuse type and ratings @ 117 VAC operation: 1.5 Amp 3AG slow-blow mains fuse
0.5 Amp 3AG slow-blow logic fuse
Fuse type and ratings @ 230 VAC operation: 0.75 Amp 3AG slow-blow mains fuse
0.25 Amp 3AG slow-blow logic fuse
Moving Magnet input impedance: 5-step user adjustable via fixed low-noise resistors.
25, 50, 100, 200 and 47000 ohms.
Moving Coil input impedance: 5-step user adjustable via multi-tap autoformer:
25, 50, 100, 200 and 400 ohms.
Input Termination Capacitance: Front Panel Selectable in 10 picofarad steps from 10 to 1100 pF (1.1nF)
Residual input capacitance less than 40 pF.
Gain: 4-step user adjustable, 50, 55, 60 and 65 dB active gain at 1 kHz referred to the FIXED output jack into a
10Kohm load. Additional gain available via the MC input's step-up autoformer. See Owner's Manual for discussion.
Deviation from RIAA curve: Less than +0.5 / -0.3 dB from 20 Hz to 20 kHz at any gain setting.
Typically less than +/- 1 dB from 10 Hz to 100 kHz
Inter-channel differential phase: Less than 4 degrees from 20 Hz to 20 kHz at any gain setting.
Typically less than 2 degrees.
Inter-channel differential gain: Less than +/- 0.5 dB from 20 Hz to 20 kHz at any gain setting.
Dynamic Range: 101 dB @ 1 kHz, 1% THD measured with 200 ohm source, 47Kohm input, @ 55dB Gain
97 dB @ 1 kHz, 0.1% THD
THD: 0.0042% at 1V output @1kHz
Maximum LINE input level: +30.6dBu @ 1KHz for an output of +29.3dBu @ 0.07% THD
26.5Vrms @ 1KHz for an output of 22.8Vrms @ 0.07% THD
Maximum Output: +27dBm @ 1KHz with 3% THD into 100Kohm load
FIXed Output impedance: 150 ohms. Minimum suggested load greater than 1500 ohms.
VARIable Output impedance: 75 ohms. Minimum suggested load greater than 600 ohms.
|
Variable Output |
|
GAIN setting |
Fixed Output |
9:00 |
12:00 |
V/C FULL |
MM Noise (S+N+D) / (N+D): |
50 dB: |
86dB |
108dB |
99dB |
86dB |
200 ohm source, 47Kohm input
A-weighted Referred to 2.54 mV
rms @ 1 kHz |
55 dB: |
84dB |
108dB |
99dB |
85dB |
60 dB: |
80dB |
108dB |
94dB |
80dB |
65 dB: |
75dB |
108dB |
89dB |
75dB |
|
|
|
|
|
|
MC Noise (S+N+D) / (N+D): |
50 dB: |
84dB |
108dB |
98dB |
85dB |
100 ohm source, 100 ohm input
A-weighted Referred to 0.5 mV
rms @ 1 kHz and rated Input Z |
55 dB: |
80dB |
108dB |
95dB |
81dB |
60 dB: |
75dB |
108dB |
90dB |
76dB |
65 dB: |
70dB |
107dB |
85dB |
71dB |
Get the Owner's Manual PDF:
Manley Steelhead Version 1 Serial Code MSH### 6/2001-11/2002
Manley Steelhead Version 2 w/LINE input Serial Code MSHL### 11/2002 - present
extra: Manley Steelhead Version 2 Owner's Manual in Japanese
Pinout for the DIN MC2 input on Version 1 and 1.5 ONLY (Version 2 changed to RCA connectors):
The pinout of the DIN on the Steelhead Version 1 and 1.5 was not in the manual! Shoot.
The pinout reads 1,4,2,5,3 if you are looking from the rear face from left to right (clockwise)
Pin 1: red left high +
Pin 2: ground
Pin 3: white right high +
Pin 4: green left low -
Pin 5: blue right low -
Power consumption: 100 watts
Outboard Power Supply: is factory set for 100V, 120V or 220-240VAC operation
for original destination country's mains voltage.
Operating Mains Voltage: 120 to 240VAC operation changeable with power transformer re-wiring via internal switch and fuse value change. 100VAC operation changeover achieved via rewiring of power transformer PCB.
Mains Voltage Frequency: 50~ 60Hz
Unit weight: Steelhead: 15 lbs.
PSU: 18 lbs.
Chassis dimensions: Steelhead: 19 wide x 3.5 tall x 15.5 deep
PSU: 13.5 wide x 4.5 tall x 11.375 deep
Minimum mounting allocation footprint including all projecting parts and controls:
Steelhead: 19 wide x 4.125 tall x 18 deep
(allow an additional 6 inches depth for PSU umbilical cord projecting out in the center)
PSU: 13.5 wide x 4.625 tall x 12.5 deep
(allow an additional 6 inches depth for PSU umbilical cord projecting out in the left)

Rear view of Version 2 Steelhead showing cable spread measurements. (Click on the pic for a bigger rear view.)
Your phono input cables need to be able to spread 9" apart.
Your LINE input RCA cables need to be able to spread 12.250" apart.
Your Output cables need to be able to spread 15" apart.
The chassis itself is 17" wide. The faceplate is 19" wide.

This is a picture of the Steelhead Power supply. You can hide it somewhere out of the way.
As of November 2005 the PSU has a BLUE LED instead of a RED one. Because you asked